Are 3D printed homes legal in Florida?

Yes. The Florida Building Code does not prohibit concrete additive construction, so 3D printed concrete homes can be permitted in Florida. There is no blanket statewide approval: each project is permitted through one of Florida's recognized compliance pathways, in practice usually project-specific engineering by a licensed Florida engineer, and standard local building department review. Statewide routes such as Florida Product Approval and a Miami-Dade Notice of Acceptance (NOA) have defined scopes and limits and do not replace local review. We will work through that project-by-project approval process in Southwest Florida.

Can you get a mortgage for a 3D printed house?

Yes, though it takes the right lender. A properly permitted, code-compliant, appraised 3D printed concrete home is real property like any other; the challenge is that appraisers need comparable sales data, which is limited today. Conventional approval depends on the appraiser's ability to find comparables, while portfolio lenders, construction lenders, and some regional banks are more flexible. FHA and VA loans have specific property standards a compliant concrete home can meet. We recommend engaging a lender early and being transparent about the construction method. As more 3D printed homes are completed and sold in Florida, financing will become more straightforward.

How much does a 3D printed home cost in Florida?

The total cost of a 3D printed home in Florida depends on size, design complexity, site conditions, and finish level, the same variables that affect any construction project. The proposed Coastal Monolithic scope is the printed concrete wall system. Reinforcement, grout, insulation, moisture control, coatings and finishes depend on the engineered assembly and may require separate work, so the shell is not a guaranteed bundle of eliminated trades. Total project cost, including foundation, MEP, roofing, windows, doors, and interior finishes, depends on the design, the site, and the finish level. See our dedicated 3D printed home cost page for the current planning estimate. Insurance, energy, and maintenance outcomes vary by insurer, design, and site; we do not promise specific savings. For a specific project, reach out directly. We will tell you honestly whether the numbers work for your site and scope.

Will a 3D printed home lower my homeowner insurance in Florida?

Florida homeowner insurance is among the most expensive in the nation, and construction type is one of several factors an insurer can weigh. Florida law requires insurers to offer wind mitigation credits based on the features documented on the Uniform Mitigation Verification Inspection, which include building code, region, roof slope, roof covering, roof deck attachment, roof-to-wall attachment, roof geometry, sealed roof deck, and opening protection. A printed concrete wall is a strong wall assembly, but insurance outcomes are not automatic and depend on the insurer, the home design, the location, and a licensed inspection. Coastal Monolithic does not promise insurance savings or quote a percentage, and we recommend getting a wind mitigation inspection early in planning. See our wind mitigation guide for a category-by-category walkthrough.

Can a 3D printed home be built in a Florida HVHZ (High Velocity Hurricane Zone)?

It depends on the project. The High Velocity Hurricane Zone (HVHZ) applies to Miami-Dade and Broward counties and sets the most stringent wind resistance requirements in the Florida Building Code. Whether any wall system can be used in an HVHZ project depends on project-specific engineering and local plan review. We do not claim blanket HVHZ approval; each project is engineered and reviewed on its own merits. Southwest Florida counties, including Collier, Lee, Charlotte, Sarasota, Manatee, and Pinellas, are not in the HVHZ but are in the Wind-Borne Debris Region and are subject to Florida's coastal construction requirements. Those requirements are addressed through the project's licensed engineering.

How does 3D printed concrete construction compare to ICF (Insulated Concrete Forms) in Florida?

Both 3D printed concrete and ICF (Insulated Concrete Forms) are concrete-based construction methods that outperform wood-frame in Florida's hurricane and insurance environment. The key differences: ICF uses pre-formed foam blocks filled with poured concrete, which requires formwork assembly, rebar placement, and a concrete pour. It is a multi-step, labor-intensive process. 3D printed concrete builds the printed concrete wall system through robotic wall printing, which can reduce the number of separate exterior wall trades to coordinate. What is included beyond the printed concrete wall, such as reinforcement, grout, insulation, moisture control, and coatings, depends on the engineered assembly and may be separate work. There are no forms to assemble and no pour to schedule for the printed wall itself. For builders evaluating both options, the 3DCP approach may offer a shorter shell phase and fewer trades to sequence, subject to the project's engineered assembly.

Are 3D printed concrete homes hurricane proof?

No structure is hurricane proof. That claim does not exist in engineering or building code. What the Coastal Monolithic wall system is: a monolithic concrete wall designed and engineered for high coastal wind loads, with the wall design, reinforcement, foundation, roof connections and openings brought together through project-specific engineering and local plan review. The jointless concrete wall has no mortar joints to fail, no wood framing to fracture, and no stucco seams to dislodge under wind pressure. The most hurricane-resistant residential structures share several characteristics: monolithic construction with no joints or seams, high-strength materials, a continuous load path from roof to foundation, and protected openings. In a high-wind event, the roof and the openings carry much of the outcome, which is why the whole assembly is engineered together. FEMA publishes safe-room guidance (FEMA P-361) for extreme-wind events; that guidance informs design, but FEMA does not certify the product. The honest language is this: designed for resilience, engineered to reduce vulnerability. Every project still requires project-specific engineering, and no structure eliminates all risk from a major storm.

How long will a 3D printed house last?

A properly constructed 3D printed concrete home is designed for a long service life, comparable to a well-built concrete structure, provided the concrete mix, construction quality, and building-envelope upkeep are all maintained. The material has no inherent expiration; longevity depends on those factors. The monolithic, jointless construction removes several of the failure points that degrade conventional homes: no mortar joint to crack, no wood framing to rot, and no stucco seam to admit water. Concrete structures built in the mid-20th century are still standing across Florida. We do not publish a specific year figure, because lifespan depends on how the home is built and maintained.

Do 3D printed homes crack?

All concrete can develop minor surface cracks over time, particularly hairline cracks from thermal expansion and contraction. This is normal for concrete and does not indicate structural failure. The key distinction is between cosmetic surface cracking and structural cracking. The monolithic, jointless construction method used by Coastal Monolithic eliminates the most common crack initiation points in conventional construction: mortar joints, framing connections, and material transitions. The high-strength mix is more resistant to cracking than standard concrete. Structural cracking in a properly designed and constructed concrete home is rare. Any surface cracks that do appear are typically cosmetic and can be addressed with standard concrete repair methods.

Are 3D printed homes mold proof?

Concrete itself does not support mold growth the way wood does. Mold requires an organic food source, and concrete does not provide one. However, no building is entirely mold-proof: mold can grow on dust, dirt, or organic material that accumulates on any surface, including concrete. The more important factor is moisture management. The high-performance envelope used in the Coastal Monolithic wall system is designed to control moisture infiltration and vapor movement, which is the primary driver of mold in Florida homes. A properly designed and constructed concrete home with a high-performance envelope is significantly more resistant to mold than wood-frame construction, where moisture can penetrate framing cavities and create ideal mold conditions.

What is the biggest problem with 3D printing in construction?

The most significant challenges in 3D printed construction are permitting, financing, and market familiarity, not the technology itself. The technology has a documented track record: the licensed platform Coastal Monolithic operates has completed structures in North America, including residential and other deployments. The practical challenges are: (1) Permitting requires independent code documentation or an equivalent engineering pathway, which not all 3D printing companies have. (2) Appraisers and lenders are still developing familiarity with the product. (3) The construction industry is conservative, and adoption takes time. Coastal Monolithic addresses the permitting challenge with project-specific engineering and technical documentation. The financing and market familiarity challenges will improve as completed projects establish a track record in Southwest Florida.

What parts of the home are 3D printed?

The 3D printed system produces the structural exterior wall system: the full perimeter walls from the foundation base to the roof line. The printed wall is a structural assembly with provision in the wall build-up for the project insulation strategy and the exterior finish, delivered as one wall system. What is not 3D printed: the foundation slab, the roof system, interior partition walls, windows, doors, MEP systems, and interior finishes. Those are installed by standard trades after the wall system is complete. The printed concrete wall is the proposed scope; reinforcement, grout, insulation, moisture control, coatings and finishes depend on the engineered assembly and may require separate work. Interior partition walls are typically framed conventionally after the shell is enclosed, the same way they are in any concrete construction project.

How fast can you build a 3D printed house?

The structural shell of a single-family home can be printed in a matter of days, not weeks. The robotic system builds the printed concrete wall system through robotic wall printing. The printed concrete wall is the proposed scope; reinforcement, grout, insulation, moisture control, coatings and finishes depend on the engineered assembly and may require separate work, so the shell phase may still require coordination with other trades. It builds the printed concrete wall system directly on site, with no factory prefabrication and no panel assembly. After printing, the concrete cures before the next phase begins, so the shell phase can be shorter than a conventional multi-trade sequence. The rest of the project, including foundation, MEP, roofing, windows, doors, and interior finishes, follows the builder's normal schedule for those trades. The Coastal Monolithic model home targets a Q1 2027 break-ground in the Englewood / Port Charlotte area, contingent on funding, site, equipment, engineering, and permits.

Can Coastal Monolithic build the whole house?

No. Coastal Monolithic is a specialty shell subcontractor, not a general contractor or homebuilder. We deliver the structural shell: the printed concrete wall system from foundation to roof line, with provision in the wall build-up for the project insulation strategy, plus the technical documentation package. Everything after the shell (roofing, MEP, windows, doors, interior finishes, landscaping, and certificate of occupancy) is handled by the builder or GC managing the full project. This is intentional. The shell is what we do, and we do it at a level of quality and documentation that no general contractor can replicate in-house. The builder or GC brings the project management, subcontractor relationships, and local market knowledge. We bring the printing platform. The combination is more capable than either party alone.

Do I still need a builder or general contractor for a 3D printed home?

Yes. A licensed general contractor or builder is required to manage the full project: permitting, subcontractor coordination, inspections, and certificate of occupancy. Coastal Monolithic delivers the structural shell as a specialty subcontractor. The GC or builder is responsible for everything else: foundation, roofing, MEP, windows, doors, interior finishes, and final inspections. If you are a landowner or developer without a GC relationship, we can help you identify qualified builders in Southwest Florida who are familiar with concrete construction and interested in the 3D printed shell model. Reach out through the contact page and describe your project.

Can builders partner with Coastal Monolithic?

Yes, and builder partnerships will be the primary model. Coastal Monolithic is actively building its Southwest Florida builder network for the 2026 to 2028 pipeline. The model is straightforward: the builder manages the full project (permitting, subcontractor coordination, and certificate of occupancy). Coastal Monolithic delivers the printed concrete shell as a specialty subcontractor. The builder's existing subcontractor relationships handle everything after the shell is enclosed. Builders who have worked with ICF, tilt-up, or CBS construction will find the post-shell workflow familiar. The shell is the handoff point. If you are a licensed GC or builder in Collier, Lee, Charlotte, Sarasota, Manatee, or Pinellas County and want to add a monolithic concrete shell to your pipeline, reach out directly through the contact page at /contact.

Can landowners use 3D printed construction for their property?

Yes. Landowners in Southwest Florida who own a lot and want to build a 3D printed concrete home can engage Coastal Monolithic directly. The typical path for a landowner: (1) Reach out through the contact page and describe your site: location, lot size, zoning, and any existing restrictions. (2) We evaluate whether the site fits the platform requirements: access for the gantry system, site conditions, and local permitting environment. (3) If the site fits, we connect you with a qualified GC or builder in our network who can manage the full project. (4) Coastal Monolithic delivers the shell as a specialty subcontractor to the GC. Landowners do not need to be builders or developers. You need a site, a GC, and a project. We handle the shell.

What areas of Florida does Coastal Monolithic serve?

Coastal Monolithic serves Florida's Gulf Coast, from Naples to St. Petersburg. That corridor runs through six counties: Collier County (see /3d-printed-homes-naples, Naples), Lee County (see /3d-printed-homes-fort-myers, Fort Myers, Cape Coral), Charlotte County (see /3d-printed-homes-port-charlotte, Port Charlotte, Englewood), Sarasota County (see /3d-printed-homes-sarasota, Sarasota, Venice, North Port), Manatee County, and Pinellas County (St. Petersburg). This is the primary service area for the pilot project and the Innovation Enclave. Projects outside this corridor are evaluated on a case-by-case basis depending on site conditions, project scale, and logistics. If you have a project outside the corridor, reach out directly and describe the project. We will give you a straight answer on feasibility.

How does the builder subcontracting process work with Coastal Monolithic?

Coastal Monolithic delivers the structural shell. Your existing subcontractor relationships handle everything after the shell is enclosed. The model is designed to slot into a builder's existing workflow, not replace it. Coastal Monolithic mobilizes the robotic printing system, batches and delivers the concrete mix, prints the full wall system, and provides the technical documentation package. From that point, the builder's MEP, roofing, window, door, and interior finish subs take over exactly as they would on any concrete construction project. There is no proprietary subcontractor network you are required to use. The shell is the handoff point. Builders who have worked with ICF or tilt-up concrete will find the post-shell workflow familiar.

Do I need special subcontractors to finish a 3D printed concrete home?

No. The interior and exterior finish trades for a 3D printed concrete home are the same trades used in any concrete construction project. Electricians, plumbers, HVAC contractors, roofers, window installers, drywall crews, and finish carpenters all work the same way they would on a conventional concrete or ICF home. The concrete shell provides the structural substrate. Conduit and plumbing rough-in are planned during the design phase and accommodated in the print. There is no proprietary system that requires specialized subcontractors. If your subs have worked on concrete construction before, they can work on a 3D printed shell.

What finishes are needed after the shell is printed?

After the shell is printed and the curing verification is complete, the project transitions to standard residential construction sequencing. The finish work required is the same as any concrete or ICF home: (1) Roofing system: truss or rafter system, sheathing, underlayment, and roofing material. (2) Windows and exterior doors. (3) MEP rough-in: electrical, plumbing, and HVAC. (4) Interior partition walls: typically light-gauge steel or wood framing. (5) Drywall on interior faces of the concrete walls and partition walls. (6) Flooring, cabinetry, trim, and paint. (7) Fixture installation and final MEP connections. (8) Landscaping and site work. Final inspections and the certificate of occupancy come at the end. None of these trades are proprietary or require specialized knowledge of 3D printing. Any subcontractor experienced with concrete or ICF construction can work on a 3D printed shell. The shell is the handoff point, and everything after it is standard residential construction. The builder's existing subcontractor relationships and scheduling process apply from the shell handoff forward, and Coastal Monolithic provides the technical documentation package to support permitting and inspection throughout.

What does the inside of a 3D printed home look like?

The interior of a 3D printed concrete home looks like any well-finished concrete or ICF home. The printed concrete wall is the structural system, not the finished interior surface. Drywall is applied to the interior face of the concrete wall, the same way it is applied to any concrete or masonry wall. Interior finishes, including flooring, cabinetry, trim, and paint, are applied normally. The result is a finished interior that is indistinguishable from a conventionally built home. The concrete shell is not visible in the finished interior unless the owner specifically chooses to leave concrete exposed as a design element, which is an option some owners prefer.

Can you run electrical and plumbing through a 3D printed concrete wall?

Yes. Electrical conduit, plumbing penetrations, and HVAC chases are planned during the design phase and incorporated into the print file before construction begins, and the robotic system accommodates planned penetrations and chases in the wall system. MEP (mechanical, electrical, plumbing) rough-in is then handled by the builder's standard subcontractors, the same way it is on any concrete construction project. The key difference from wood-frame is that conduit runs, plumbing penetrations, and HVAC chases must be coordinated during the design and print preparation phase, before the print file is finalized, so they are in the correct location when the shell is complete. Post-print, electricians and plumbers work the same way they would on any concrete construction project. Coastal Monolithic coordinates with the builder's MEP subs during the design phase to ensure the print file reflects the actual MEP layout. This is a standard part of the pre-construction process.

Can you add a second story to a 3D printed home?

Multi-story 3D printed concrete construction is technically feasible and has been demonstrated on projects globally. The structural capacity of the high-strength concrete wall system supports multi-story loads. The practical considerations for a specific project depend on the design, the site, and the engineering requirements for the upper floor system. Single-story construction is the current focus for the Coastal Monolithic pilot and Innovation Enclave projects in Southwest Florida, where single-story concrete construction is the dominant residential form. Multi-story designs are a conversation for specific projects. If you have a multi-story project in mind, reach out directly and we will give you a straight answer on feasibility.

What are the site requirements for the Innovation Enclave?

The Innovation Enclave is a 20 to 25 unit residential cluster of monolithic concrete homes in Southwest Florida. The Enclave is a future phase with no set timeline. Site requirements for a planned Enclave location include: (1) Location in Collier, Lee, Charlotte, Sarasota, Manatee, or Pinellas County. (2) Sufficient acreage to support 20 to 25 residential units at a density appropriate for the zoning district. (3) Zoning that permits residential development at the target density, or a clear path to rezoning. (4) Access to utilities: water, sewer or septic, and electrical service. (5) Site conditions that support the robotic printing system: a reasonably level site with vehicle access for the gantry system and concrete delivery. (6) No deed restrictions that prohibit concrete or non-traditional construction methods. If you have a site in Southwest Florida that might fit, reach out directly. We will evaluate it honestly.

How does the Innovation Enclave builder partnership work?

The Innovation Enclave builder partnership model is designed to work with local Southwest Florida builders and general contractors who want to add a resilient, storm-designed product to their pipeline. Coastal Monolithic would deliver the printed concrete shells for all units in the cluster. The builder partner would handle MEP, roofing, windows, doors, and interior finishes for each unit, using their existing subcontractor relationships. The builder brings local market knowledge, subcontractor relationships, and construction management capacity. Coastal Monolithic brings the printing platform, technical documentation, and permitting support. The specific terms of the partnership, including revenue split, project management structure, and timeline, are negotiated on a project-by-project basis. The starting point is a direct conversation. Reach out through the contact page.

What is the timeline for the Innovation Enclave?

The Innovation Enclave is a future phase with no set timeline. The model home, a single-family home in the Englewood / Port Charlotte area, is the proving ground for the permitting pathway, construction workflow, cost structure, and market demand, and targets a Q1 2027 break-ground. Successful completion of the model home establishes the foundation for the Enclave. Builder and developer conversations for the Enclave are exploratory at this stage.

Can the Innovation Enclave be built on my land?

Potentially, yes. Coastal Monolithic is actively evaluating land partnerships in Collier, Lee, Charlotte, Sarasota, Manatee, and Pinellas counties for the Innovation Enclave. If you own land in Southwest Florida that could support a 20 to 25 unit residential cluster, we want to hear from you. The evaluation process starts with a direct conversation about the site: location, acreage, zoning, utilities, and any existing restrictions. We will give you a straight answer on whether the site fits the Enclave model and what a land partnership would look like. Reach out through the contact page and describe your site.

Does Coastal Monolithic work across Charlotte County?

Yes. Punta Gorda sits within Charlotte County, which is core to our service area along with Port Charlotte and Englewood. Builders, developers, and landowners with projects in Punta Gorda and the surrounding Charlotte County communities can reach out directly. We evaluate each site for print mobilization, access, and local permitting conditions, and we give you a straight answer on fit.

Waterfront town on Charlotte Harbor in Florida

Punta Gorda, Florida

3D Printed Concrete Homes in Punta Gorda

Concrete shell construction for Punta Gorda builders and landowners, in a waterfront city that rebuilt once already and knows exactly what it is building for.

Let's build something together Read the FAQ

Charlotte HarborCharlotte County CoveragePost-Charley FocusOne-Pass Wall Printing

A small city with a serious coastline

Punta Gorda is smaller and quieter than its neighbors, and it sits directly on Charlotte Harbor. That combination is the whole story. The city has a long, exposed waterfront, a tight-knit residential core, and a population that has already lived through a direct hurricane hit. When the conversation turns to how a house is built, this city listens closely.

Charlotte Harbor exposure

The city faces open water on the harbor, one of the most exposed shorelines in the region. Homes near the water carry real wind and storm-surge risk, and the construction method is worth thinking about carefully here.

A resilient-building culture

Punta Gorda rebuilt after 2004 with a sharper eye on construction quality. That mindset makes conversations about concrete shells and high-wind design land differently than in places that have not faced a direct hit.

Flood zones and elevation

A large share of waterfront and near-shore property sits in FEMA flood zones, where base flood elevation requirements shape the design. Those requirements are handled project by project through the engineer and local review.

A steady, discerning market

Punta Gorda draws buyers who want a coastal home that holds up and holds value. The demand for durable, low-maintenance construction is quiet but real, and it fits a monolithic concrete shell well.

A city that rebuilt once, and remembers why

Hurricane Charley made landfall at Punta Gorda in August 2004 as a Category 4 storm, one of the strongest landfalls in Southwest Florida history. The city came back, and it came back with better building on its mind.

Cat 4

Hurricane Charley came ashore at Punta Gorda in August 2004

2004

The storm that reshaped how the city approaches construction

20+ yrs

Time since Charley, and the resilience conversation has not faded

What Charley taught Punta Gorda builders

The homes that held up best were the ones with a strong, connected structural shell. Failures clustered around roof attachments, water intrusion into framing, and the joints where conventional assemblies come apart. A monolithic printed concrete wall removes the joints and connections where wood-frame construction tends to fail, which is why the conversation still matters here more than two decades later.

Built for Punta Gorda's builders and landowners

Punta Gorda Builders

Add a printed concrete wall system to your Punta Gorda pipeline. Robotic wall printing builds the printed concrete wall system, which can help keep a waterfront build on schedule.

Discuss Your Project

Waterfront Landowners

Holding a lot near Charlotte Harbor? A single print pass replaces the usual multi-trade sequence, and the monolithic shell is designed for the coastal exposure that comes with the address.

Discuss Your Site

Homeowners Rebuilding

Replacing an older or storm-damaged home in Punta Gorda? A printed concrete wall system replaces the joints and wood framing with a continuous deposited concrete wall.

Learn About Rebuilding

Investors

Punta Gorda rental and resale demand is steady and rooted in waterfront appeal. Concrete trims the rot, termite, and stucco upkeep that quietly erodes returns over time.

Investor Overview

Aerial view of a Southwest Florida harbor and waterfront

Service Area

Punta Gorda and the rest of Charlotte County

Punta Gorda sits on the southern shore of the Peace River at Charlotte Harbor, within our Charlotte County coverage alongside Port Charlotte, Englewood, and the surrounding communities. Sites in neighboring Sarasota or Lee counties are considered individually. Coastal Monolithic is pre-construction; the model home targets a Q1 2027 break-ground.

A waterfront town that takes building seriously.

Punta Gorda is the kind of place where people notice how a house is put together. The harbor, the history, and a population that has been through a major storm all push the conversation toward durability instead of decoration.

That suits concrete. A printed concrete wall system is designed to answer the questions this city already asks, with walls engineered to the high coastal wind loads for the site instead of a collection of joints and connections.

Punta Gorda and the rest of Charlotte County are core to what we do. If you have a lot, a plan, or a question, send it over and we will give you a plain answer, usually within two business days.

Common questions about Punta Gorda projects

Punta Gorda sits on Charlotte Harbor, one of the most exposed waterfront locations in Southwest Florida. Hurricane Charley came ashore here in August 2004 as a Category 4 storm and reshaped how the city thinks about building. More than two decades later, that history still drives local interest in construction methods that reduce wind and water vulnerability. A monolithic concrete shell is designed for that exact concern, with the walls engineered to carry the high coastal wind loads for the site.

Much of Punta Gorda's waterfront and near-shore property falls within FEMA flood zones, and building in those areas involves base flood elevation requirements that are addressed in the project design and engineering. The flood zone, the required elevation, and how the finished floor is set are project-specific factors the licensed engineer and the local building department confirm during plan review. We coordinate with that process on every project rather than assuming a single answer applies to the whole city. Charlotte County publishes current flood zone maps and local permitting guidance through its building and flood management offices, and we point every project to that current local resource rather than a fixed answer.

The printed structural shell is planned to print in a short window once the site is prepared and permits are in place, though Coastal Monolithic has not yet completed a project to confirm that in practice. Total project timeline depends on site conditions, flood and elevation requirements, design complexity, and the builder's schedule for MEP, roofing, windows, and interior finishes. A printed wall does not eliminate the risk of roof or joint failures elsewhere in the home; those depend on the roof and connection design. Coastal Monolithic delivers the structural shell as a specialty subcontractor, and the builder managing the project handles everything after the shell is enclosed.

A question about your Punta Gorda lot not answered above?

Full FAQ page Port Charlotte page Email Jack directly

Port Charlotte Fort Myers Cape Coral Naples Sarasota Venice North Port All SWFL

Start your Punta Gorda project

Punta Gorda builders, developers, and landowners: send us the lot and the drawings. We get back to you within a day or two.

Let's build something together Email Jack directly

Charlotte Harbor · Charlotte County Coverage · One-Pass Printed Shells · Punta Gorda, Florida

3D Printed Concrete Homes in Punta Gorda

A small city with a serious coastline

Charlotte Harbor exposure

A resilient-building culture

Flood zones and elevation

A steady, discerning market

A city that rebuilt once, and remembers why

What Charley taught Punta Gorda builders

Built for Punta Gorda's builders and landowners

Punta Gorda Builders

Waterfront Landowners

Homeowners Rebuilding

Investors

Punta Gorda and the rest of Charlotte County

Punta Gorda

Port Charlotte

Englewood

Rotonda West

Deep Creek

Harbour Heights

Charlotte Harbor

Grove City

A waterfront town that takes building seriously.

Common questions about Punta Gorda projects

Start your Punta Gorda project